Categories
CAMing

Sprutcam Licensing Trick

I do not recall how much I paid for my Sprutcam license, although I imagine it must have been somewhere in the vicinity of $1500.00. There are many CAM software suites out there, and although Sprutcam has managed to piss me off countless times, I am still confident it is one of the best deals out there.

What truly pisses me about Sprutcam, as well as any other software based on the ultimate form of mistrust, is the darned dongle crap. It truly bugs me for two reasons:

1. Dongles imply that you can only use the SW on one computer (which is of course the main reason why there is a dongle in the first place) and

2. I still wake up at 3:00 AM in the morning fearing my dongle has been lost in which case I have miserably wasted whatever amount of money I paid for in the first place.

Item #2 will plague me forever as there is no legal way of copying this dongle in case something heinous happens. Item #1, however, I set myself to solve.

But why?

Well, as it turns out, Murphy’s law makes it imminent that the most that you need a software to run in only one computer, the more that you will need to use it in two.

My main computer is inside the house, on the second floor, might I add. This is where I work my designs and do the CAMing. As I specified, it is in the second floor which brings us to the Murphy’s law stating it is 100% certain the better you have done a CAM in the second floor of your house, the more probable it becomes you will find bugs while you are in the first floor.

Of course I can’t have my PCNC1100 milling machine in my second floor, but I can’t have the main computer on the first floor either, so what to do?

Well, I decided to install a second computer to do quick fixes whenever I am running a job in the garage, where the CNC machine is located. Unfortunately, for this to work, I would need to be moving the dongle up and down on a continuous basis. This is a clear violation to the Murphy’s law which states that as soon as you start moving up and down that ridiculously expensive item you dread to lose, you will either loose it or misplace it whenever you need it the most!

Once again, what to do?

I thought of installing an USB switch so that I could remotely specify which computer is entitled to use the USB dongle. It doesn’t work 100% perfect because every now and then the USB switch develops a temper, but for the most part it has become the solution.

This is the USB Switch I am using, and you can find it here: http://www.amazon.com/Cables-Unlimted-USB-Automatic-Switchbox/dp/B0006N213K/ref=sr_1_10?ie=UTF8&qid=1393466095&sr=8-10&keywords=cables+unlimited+usb+switch

This solution still poses a problem. Sure, you can now have two computers to claim the dongle, but how on Earth are you going to hook two computers into this thing when one of them is on the second floor and the second one is on the garage? USB standards forbids such a long cable!

No worries! The solution comes in the form of an USB cord expander which utilizes a CAT5 cable connection, or this: http://www.amazon.com/SANOXY%C2%AE-over-Extension-Cable-Adapter/dp/B003BDMK3S/ref=sr_1_1?ie=UTF8&qid=1393466340&sr=8-1&keywords=USb+RJ45

I have been using this solution for three years. In that time, one of the USB extenders died so I had to replace it. But man, at less than $10, who is counting?

So here you go! An entire solution for less than $30 which beats buying two licenses of Sprutcam. Now, if I were a Rockefellarian, then I could buy 2 licenses. Although the truth is if I was a Rockefellarian, I would have a shop so awesomely big, my main computer would be besides the milling machine.

2 replies on “Sprutcam Licensing Trick”

Hello!
Why you don’t use the network license for the SprutCAM?
In this case you can put the dongle in the one computer (on the second floor), configure the network and happy to work on the computer around your cnc machine.

Intriguing… Wasn’t aware that was an option! Well, right now it is a complete impossibility as the dongle died last year and they moved me to a software license. In a few months, however, I will have to buy a new license so I will give that a try. Thanks for the pointer!

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.